How to add and reset GE/Jasco products on Hubitat Elevation hub
Authored by: Support.com Tech Pro Team
1. Introduction
How to add and reset GE/Jasco products on Hubitat Elevation hub
2. Resolution
Link Bulb
Product Number
Device Type
Protocol
NIL
Bulb
Zigbee
Factory Reset
Turn OFF the light for 3 seconds.
Turn ON the light for 3 seconds
Repeat this process 5 times
The bulb will dim and then flash once when successfully reset.
Join the Zigbee Network
From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
Turn the bulb on.
The bulb will flash when connected to the hub.
Leaving the Zigbee Network
From the device's details page, select Remove Device, then Remove.
Plug-in Dimmer
Product Number
Device Type
Protocol
12718
Dimmer
Z-Wave
Factory Reset
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
A single press and release of the manual/program button on the device to perform a general exclusion.
12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
Join the Z-Wave Network
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
A single press and release of the manual/program button on the device to include it in the network.
Exclusion from the Z-Wave Network
From the device's details page, select Remove Device, then Remove
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
A single press and release of the manual/program button on the device to exclude it from the network.
Product Number
Device Type
Protocol
28167
Dimmer
Z-Wave Plus
Factory Reset
I plugged in, and unplug the Dimmer from the receptacle.
Press and hold the top button for at least 3 seconds while you plug the dimmer into a receptacle.
Join the Z-Wave Network
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
A single press and release of the manual/program button on the device to include it in the network.
Exclusion from the Z-Wave Network
From the device's details page, select Remove Device, then Remove
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
A single press and release of the manual/program button on the device to exclude it from the network.
Product Number
Device Type
Protocol
28169
Dimmer
Z-Wave Plus
Factory Reset
I plugged in, and unplug the Dimmer from the receptacle.
Press and hold the top button for at least 3 seconds while you plug the dimmer into a receptacle.
Join the Z-Wave Network
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
A single press and release of the manual/program button on the device to include it in the network.
Exclusion from the Z-Wave Network
From the device's details page, select Remove Device, then Remove
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
A single press and release of the manual/program button on the device to exclude it from the network.
Plug-in Switch
Product Number
Device Type
Protocol
12719/ZW4101
Switch
Z-Wave
Factory Reset
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
A single press and release of the manual/program button on the device to perform a general exclusion.
12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
Join the Z-Wave Network
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
A single press and release of the manual/program button on the device to include it in the network.
Exclusion from the Z-Wave Network
From the device's details page, select Remove Device, then Remove
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
A single press and release of the manual/program button on the device to exclude it from the network.
Product Number
Device Type
Protocol
45853
Switch
Zigbee
Factory Reset
Unplug the switch.
Hold the button and plug in the switch.
Keep the button held down for 10 seconds.
Join the Zigbee Network
Remove power from the dimmer at the circuit breaker.
From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
Unplug the switch.
Hold the button and plug in the switch.
Keep the button held down for 10 seconds.
Leaving the Zigbee Network
From the device's details page, select Remove Device, then Remove.
Unplug the switch.
Hold the button and plug in the switch.
Keep the button held down for 10 seconds.
Outdoor Plug-in Switch
Product Number
Device Type
Protocol
12720/ZW4201
Switch
Z-Wave
Factory Reset
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
A single press and release of the manual/program button on the device to perform a general exclusion.
12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
Join the Z-Wave Network
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
A single press and release of the manual/program button on the device to include it in the network.
Exclusion from the Z-Wave Network
From the device's details page, select Remove Device, then Remove
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
A single press and release of the manual/program button on the device to exclude it from the network.
Product Number
Device Type
Protocol
14284
Switch
Z-Wave Plus
Factory Reset
Unplug the switch from the outlet
Press and hold the manual/program button on the switch for at least three seconds while you plug the switch into an outlet
Join the Z-Wave Network
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
A single press and release of the manual/program button on the device to include it in the network.
Exclusion from the Z-Wave Network
From the device's details page, select Remove Device, then Remove
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
A single press and release of the manual/program button on the device to exclude it from the network.
In-Wall Outlet
Product Number
Device Type
Protocol
12721
Outlet
Z-Wave
Factory Reset
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
A single press and release of the manual/program button on the device to perform a general exclusion.
12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
Join the Z-Wave Network
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
A single press and release of the manual/program button on the device to include it in the network.
Exclusion from the Z-Wave Network
From the device's details page, select Remove Device, then Remove
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
A single press and release of the manual/program button on the device to exclude it from the network.
In-Wall Switch
Product Number
Device Type
Protocol
12722
Switch
Z-Wave
Factory Reset
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
Press and release the top or bottom of the wireless smart dimmer rocker to perform a general exclusion.
12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
Join the Z-Wave Network
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
Press and release the top or bottom of the wireless smart dimmer rocker to add it to the network.
Exclusion from the Z-Wave Network
From the device's details page, select Remove Device, then Remove
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
Press and release the top or bottom of the wireless smart dimmer rocker to exclude it from the network.
Product Number
Device Type
Protocol
14291
Switch
Z-Wave Plus
Factory Reset
Quickly press the ON (Top) button 3 times then immediately press the OFF (Bottom) button 3 times.
The LED will flash ON/OFF 5 times when completed successfully.
Join the Z-Wave Network
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
Press and release the top or bottom of the wireless smart switch rocker to add it to the network.
Exclusion from the Z-Wave Network
From the device's details page, select Remove Device, then Remove
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
Press and release the top or bottom of the wireless smart switch rocker to exclude it from the network.
While some switches have a small tab to pull out, commonly referred to as an Air Gap, certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains-powered device is refusing to join Hubitat Elevationâ„¢, try Z-Wave Exclude and then cut the power at the breaker box for 30 seconds before attempting the discovery procedure again.
Product Number
Device Type
Protocol
45856
Switch
Zigbee
Factory Reset
Tap the top of the rocker (ON Switch) with 10 quick short presses.
Join the Zigbee Network
Remove power from the dimmer at the circuit breaker.
From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
Restore power to the Smart Dimmer at the circuit breaker
Pairing Begins Automatically: LED Status Indicator flashes as the Smart Dimmer automatically scans for a compatible network controller to pair with.
After the Smart Dimmer is located and paired to the ZigBee network, the LED Status Indicator will stop flashing and the Smart Dimmer.
LED Status Indicator stops flashing if a timeout occurs: Auto-Scan mode will eventually time out if the device has not joined a ZigBee network. Press and release the front panel to restart the pairing process following a timeout.
Leaving the Zigbee Network
From the device's details page, select Remove Device, then Remove.
Product Number
Device Type
Protocol
46201
Switch
Z-Wave Plus
Factory Reset
Quickly press the ON (Top) button 3 times then immediately press the OFF (Bottom) button 3 times.
The LED will flash ON/OFF 5 times when completed successfully.
Join the Z-Wave Network
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
Press and release the top or bottom of the wireless smart switch rocker to add it to the network.
Exclusion from the Z-Wave Network
From the device's details page, select Remove Device, then Remove
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
Press and release the top or bottom of the wireless smart switch rocker to exclude it from the network.
While some switches have a small tab to pull out, commonly referred to as an Air Gap, certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains-powered device is refusing to join Hubitat Elevationâ„¢, try Z-Wave Exclude and then cut the power at the breaker box for 30 seconds before attempting the discovery procedure again.
In-Wall Dimmer
Product Number
Device Type
Protocol
12724
Dimmer
Z-Wave
Factory Reset
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
Press and release the top or bottom of the wireless smart dimmer rocker to perform a general exclusion.
12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
Join the Z-Wave Network
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
Press and release the top or bottom of the wireless smart dimmer rocker to add it to the network.
Exclusion from the Z-Wave Network
From the device's details page, select Remove Device, then Remove
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
Press and release the top or bottom of the wireless smart dimmer rocker to exclude it from the network.
Product Number
Device Type
Protocol
14294
Dimmer
Z-Wave Plus
Factory Reset
Quickly press the ON (Top) button 3 times then immediately press the OFF (Bottom) button 3 times.
The LED will flash ON/OFF 5 times when completed successfully.
Join the Z-Wave Network
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
Press and release the top or bottom of the wireless smart dimmer rocker to add it to the network.
Exclusion from the Z-Wave Network
From the device's details page, select Remove Device, then Remove
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
Press and release the top or bottom of the wireless smart dimmer rocker to exclude it from the network.
While some switches have a small tab to pull out, commonly referred to as an Air Gap, certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains-powered device is refusing to join Hubitat Elevationâ„¢, try Z-Wave Exclude and then cut the power at the breaker box for 30 seconds before attempting the discovery procedure again.
Product Number
Device Type
Protocol
45857
Dimmer
Zigbee
Factory Reset
Lift the air-gap switch at the bottom of the rocker to the OFF position to power down the device.
Hold down the UP button
Push-In the air-gap switch to the ON position to power up the device.
Release the UP button within 4 seconds of powering up.
Join the Zigbee Network
Remove power from the dimmer at the circuit breaker.
From the Hubitat Web Interface home page, select Zigbee on the Device Discovery page to start device discovery.
Restore power to the Smart Dimmer at the circuit breaker
Pairing Begins Automatically: LED Status Indicator flashes as the Smart Dimmer automatically scans for a compatible network controller to pair with.
After the Smart Dimmer is located and paired to the ZigBee network, the LED Status Indicator will stop flashing and the Smart Dimmer.
LED Status Indicator stops flashing if a timeout occurs: Auto-Scan mode will eventually time out if the device has not joined a ZigBee network. Press and release the front panel to restart the pairing process following a timeout.
Leaving the Zigbee Network
From the device's details page, select Remove Device, then Remove.
In-Wall Toggle Switch
Product Number
Device Type
Protocol
12727
Switch
Z-Wave
Factory Reset
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
Press up and release the toggle switch to perform a general exclusion.
12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
Join the Z-Wave Network
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
Press up and release the toggle switch to include it in the network.
Exclusion from the Z-Wave Network
From the device's details page, select Remove Device, then Remove
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
Press up and release the toggle switch to exclude it from the network.
In-Wall Toggle Dimmer
Product Number
Device Type
Protocol
12729
Dimmer
Z-Wave
Factory Reset
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
Press up and release the toggle switch to perform a general exclusion.
12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
Join the Z-Wave Network
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
Press up and release the toggle switch to include it in the network.
Exclusion from the Z-Wave Network
From the device's details page, select Remove Device, then Remove
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
Press up and release the toggle switch to exclude it from the network.
In-Wall Fan Control
Product Number
Device Type
Protocol
12730/ZW4002
Fan Controller
Z-Wave
Factory Reset
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
Press and release the top or bottom of the wireless fan control rocker to perform a general exclusion.
12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
Join the Z-Wave Network
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
Press and release the top or bottom of the wireless fan control rocker to add it to the network.
Exclusion from the Z-Wave Network
From the device's details page, select Remove Device, then Remove
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
Press and release the top or bottom of the wireless fan control rocker to exclude it from the network.
Product Number
Device Type
Protocol
14287
Fan Controller
Z-Wave Plus
Factory Reset
Quickly press the ON (Top) button 3 times then immediately press the OFF (Bottom) button 3 times.
The LED will flash ON/OFF 5 times when completed successfully.
Join the Z-Wave Network
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
Press and release the top or bottom of the wireless fan control rocker to add it to the network.
Exclusion from the Z-Wave Network
From the device's details page, select Remove Device, then Remove
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
Press and release the top or bottom of the wireless smart fan control rocker to exclude it from the network.
While some switches have a small tab to pull out, commonly referred to as an Air Gap, certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains-powered device is refusing to join Hubitat Elevationâ„¢, try Z-Wave Exclude and then cut the power at the breaker box for 30 seconds before attempting the discovery procedure again.
In-Wall Tamper Resistant Outlet
Product Number
Device Type
Protocol
14288
Outlet
Z-Wave Plus
Factory Reset
Press the manual/program button 3 times, then press and hold the button for at least 3 seconds. The LED will flash 5 times to confirm.
Join the Z-Wave Network
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
A single press and release of the manual/program button on the device to include it in the network.
Exclusion from the Z-Wave Network
From the device's details page, select Remove Device, then Remove
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
A single press and release of the manual/program button on the device to exclude it from the network.
Smart Motion Switch
Product Number
Device Type
Protocol
26931
Switch
Z-Wave Plus
Factory Reset
Press and release the top button 10 times within 5 seconds.
Join the Z-Wave Network
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
Press and release the top or bottom button on the smart switch to include it in the network.
Exclusion from the Z-Wave Network
From the device's details page, select Remove Device, then Remove
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
Press and release the top or bottom button on the smart switch to exclude it from the network.
Product Number
Device Type
Protocol
26933
Switch
Z-Wave Plus
Factory Reset
Press and release the top button 10 times within 5 seconds. The LED will flash 3 times quickly confirming the change
Join the Z-Wave Network
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
Press and release the top or bottom button on the smart switch to include it in the network.
Exclusion from the Z-Wave Network
From the device's details page, select Remove Device, then Remove
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
Press and release the top button on the smart switch to exclude it from the network.
Hinge Pin Smart Door Sensor
Product Number
Device Type
Protocol
32563/ZW6301
Contact Sensor
Z-Wave Plus
Factory Reset
Press and release the program button 10 times quickly.
The LED light will flash approximately eight times.
Join the Z-Wave Network
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
A single press and release of the program button on the device to include it in the network.
Exclusion from the Z-Wave Network
From the device's details page, select Remove Device, then Remove
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
A single press and release of the program button on the device to exclude it from the network.
Enbrighten Smart Dimmer
Product Number
Device Type
Protocol
46203
Dimmer
Z-Wave Plus
Factory Reset
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
Press and release the top or bottom of the wireless smart dimmer rocker to perform a general exclusion.
12xxx series devices do not support factory reset from the device. A Z-Wave general exclusion is the only option.
Join the Z-Wave Network
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Inclusion on the Device Discovery page.
Press and release the top or bottom of the wireless smart dimmer rocker to add it to the network.
Exclusion from the Z-Wave Network
From the device's details page, select Remove Device, then Remove
From the Hubitat Web Interface home page, select Z-Wave, then Start Z-Wave Exclusion on the Device Discovery page.
Press and release the top or bottom of the wireless smart dimmer rocker to exclude it from the network.
While some switches have a small tab to pull out, commonly referred to as an Air Gap, certain older GE switches do not disable power to the internal Z-Wave radio when the air gap is pulled. In such cases, where a mains-powered device is refusing to join Hubitat Elevationâ„¢, try Z-Wave Exclude and then cut the power at the breaker box for 30 seconds before attempting the discovery procedure again.
.png)
